The Custom Shop Urethane Bed Liner comes with 2K. 2K protective coating means that you need one more thing with the liner base to make the usable mixture. In this case, it’s the hardener. You need to use the liner and the hardener in a 3:1 ratio and remember that at 72°F its Pot life is 45-60 mins. If you’re looking for a spray in bedliner that allows you to get the perfect tint according to your preference then this one is your go-to guy.” Key the surface to ensure good adhesion. The coarseness of the sandpaper you use for this will vary depending on the surface you are painting – we recommend you use: There’s another issue of odor. It might emit unpleasant odors right after applying them. Its better you proceed with the task keeping at least a few days in hand before any delivery.

The brush offers much more control in the area you cover and you can keep the mess relatively contained, which is a good thing. Painting bed liners with the brush also guarantees better adhesion, since you are using some force when you paint. Using masking papers or plastic making films, you should then cover the areas where you won’t be applying the product. That should be done carefully because it can be very inconvenient to remove overspray later on.You’ll find it a lot faster than painting with a brush, but chances are you’ll need an air compressor to work the gun and that could be a whole other headache for some.

If you invest in a good product, it could even help dampen the noise and vibrations of the cargo on the vehicle. With all these benefits, what features should we look for when buying a bed liner kit ? Durability These are the features we looked to when we organized the 10 best spray can bedliners you can afford in this very article. The mixing process of this bedliner is as easy as it goes. You just need to maintain a 3 (bedliner):1 (hardener) ratio and the tint can be used up to 10%. This one has the quality to give you the most anticipated results. You can depend on this guy to take care of all kinds of issues by ensuring all types of protection.Many people look for blended polyurethane like in Al’s Liner ALS-BL or just urethane, but polymer also works surprisingly well. DIY polyurethane is stiffer, while polymer provides a smoother coating. The spray gun offers a more professional finish. You won’t see the marks of errors and each individual stroke that went into the paint job. This HERCULINER Aerosol Spray Bed Liner comes with tough textured polyurethane formula. So the coating without any doubt will be a dependable and long-lasting one. The layer won’t just fade away after a short period of time like the low-quality ones. This aerosol-based spray in the bedliner is better than most ordinary water-based products. This kit has 4 x 21 fl. oz. cans of tintable bedliner base, 4 x 3 fl. oz. bottles of color tint, 4 x 8 fl. oz. cans of hardener, and 1 x spray Gun. There’s a user guide manual too that’ll help you with the mixing process. You can get an anticipated outcome with any available color or multicolor. Just choose the tint! While two coats of bed liner paint are generally sufficient for most applications, a third coat may be a good idea to increase durability around areas that are likely to see the most wear.

Protective features aren’t the only thing in a bedliner that matters. Speaking of which, If you’re looking for something that can give you the glossy finish at the end then this one is your go-to guy. Because its specialty is that it offers a low luster finish. All that’s left is mixing the color to get the anticipated result with the color that you wished for. You can mix almost any automotive pigments. That makes it one of the best professional spray in bedliners for professional DIY services too.There are certain substances like gasoline, oil, chemicals, and solvents that react with the bedliner and damages its different attributes, especially by weakening its durability. However, the specialty of this particular bedliner is, it’s resistant to these things too. And trust me when I say this, it’s definitely an upper hand! Your bedliner choice is only as good as your application. So even if you have the best spray in bedliner, the output is up to you. Thankfully, the DIY process doesn’t have to be complicated. Bare steel, bare aluminium and laminated resin fibreglass should be primed with bed liner primer: this is available in 1K, 2K and pre-adhesion primer formulations. This also applies where painted surfaces have been scuff sanded down to bare metal: the metal should be abraded with 40 grit and primer applied. Applying Bed Liner Paint You need to add the activator and component C to the liner and mix it properly with a high viscosity mixing paddle. But make sure you don’t mix any longer than 45 seconds as it’ll get hyperactivated in that case. Another thing, before pouring the activator you need to shake it properly as it needs to be agitated. The effort you put into painting also allows for a more even spread. It’s also easy to use for those inexperienced painters (which is the majority of us, let’s face it) especially if you accidentally go in a different direction.

As with all paints, they are also easily applied to the smallest nooks and crannies where dirt and moisture tend to collect and cause problems. The ToughOX applicator is also an improvement on standard UBS spray guns in that it comes in two sections. While the trigger section is made conventionally from metal, the nozzle section is made from plastic and is designed to be semi-disposable. This makes it much more efficient to use, without the inconvenience and solvents of cleaning and giving the perfect results you would expect from a brand-new gun every time. The paint can has no shelf-life, and can be reused as needed. The water-based formula is easy to clean, making it even easier to mask your mistakes and wash off. There also isn’t a recoat window, meaning you can apply multiple coatings as you see fit. As with all paint products, correct preparation and application are essential to achieve lasting and good-looking results with bed liner paint. Let’s look at how you need to prepare your surface. Preparing A Surface For Bed Liner Paint

Preparing A Surface For Bed Liner Paint

If you are applying bed liner paint to bare wood, plywood or fibre board use smooth bed liner paint for the first coat to ensure even absorption into the surface – you won’t get this as easily with the textured version due to the rubber granules. Textured bed liner paint can then be applied as the second coat. How much paint do you need to use? Most manufacturers will give an estimate of the surface coverage for their product. A roll-on liner does give you the same customizability as spray in ones, but a large roll-on brush wouldn’t be able to get the color into those hard to reach places. If you want to use a roller, get one that’s smaller.